What do customers need to consider when ordering a stone crusher production line?
In the process of actually investigating the stone crusher production line, you will find that there are many factors affecting your final machine matching. The appropriate stone crusher production line used by others is not necessarily suitable for your own actual production environment, so the relevant crusher selection must take into account the influence of various factors, and a scientific and reasonable model collocation can be carried out. So what are the main factors that affect the customer's choice when ordering a machine? Below, let us combine the previous production experience and customer feedback suggestions to communicate with you:
First of all: the type, hardness and silicon content of the material to be crushed. Material type, hardness and silicon content is an important principle in the selection of stone crusher, the hardness of different materials is not the same, usually used Mohs hardness to indicate the hardness of the material. Mohs hardness is divided into 10 levels, the greater the Mohs hardness number, the harder the ore is, the more difficult it is to break, and vice versa. In addition, the silicon content of the material directly affects the service life of the machine parts in the later period, the greater the silicon content, the more severe the wear, at this time, it is necessary to choose what kind of working principle of the crushing machine can be used according to the specific composition it contains, otherwise, regardless of the objective actual situation on the machine, the result is often half the effort.
Among them, rocks with large silicon content and high hardness need to use jaw crusher, impact crusher, cone crusher and hydraulic roll crusher. If it is for limestone and other soft rock crushing, we recommend the use of stone hammer crusher production line.
Secondly: the water content of the material to be crushed. This is also a problem that must be taken seriously, the water content of the material will also affect the choice of crusher, when the water content is too large, the fine grained material will be due to the increase in humidity and clumping or sticking on the coarse grained material, thereby increasing the viscosity of the material, reducing the discharge speed, so that the productivity has declined. In serious cases, it will even cause blockage of the discharge port, affecting the normal production. Choosing a machine with a large water content is particularly critical at this time, which will improve the efficiency of the entire stone crusher production line and indirectly bring higher economic benefits to customers.
Third: the granularity of incoming and outgoing materials and the type of finished materials required by customers. If the feed block is too large, it is necessary to properly add the jaw crusher, otherwise it will affect the production efficiency of the crusher production line and easily cause the occurrence of choking. The same type of crusher produces different specifications of finished materials, and the smaller the specifications of finished materials, the lower the output. In addition, it is necessary to match the suitable screening system according to the type of finished materials needed by customers to avoid the waste of resources.
Fourth: the output of the crushing production line. Be sure to figure out this problem, the specific production of different stones is not the same, the harder the stone, the lower the yield. The output is also an important indicator to determine the selection of crushing equipment, the conventional understanding is that the higher the output requirements, the larger the specifications of the crushing equipment required, and the corresponding input and output will increase.
Fifth: customer processing and production methods. If the customer's production site is installed on the mine, easy to take material, in principle as long as the customer site conditions allow, in accordance with the current trend of the crusher industry, of course, the larger the model matching the better. If the customer is installed in the factory to get the incoming material processing or use the mobile crushing station for production, it is not recommended that the customer on the crusher production line is too large. As a crusher manufacturer with 30 years of production experience, we must be realistic and stand in the customer's point of view to solve the problem.
Sixth: the construction site and the existing production site. Many customers are limited by the construction site and the existing production site, not suitable for immediately on the large crusher production line, at this time, we have to ask for customers' opinions, first on a set of small crusher production line, the future conditions permit, you can consider the crusher production line to upgrade. The size of the construction site is also one of the factors that people consider when choosing a crusher. In addition, the placement of crushing equipment also affects the choice of crusher.
In summary, Shandong Sanxiang Heavy Industry Co., Ltd. customers in the crusher production line selection, all the details, need to pay attention to a lot of factors, must be taken seriously. After so many years of experience accumulation, Shandong Sanxiang Heavy machinery in communication with customers, the above problems will be consulted one by one, and then according to the specific requirements of customers for the production line supporting design work, can not be sloppy, otherwise once the actual production and then encounter problems it is not easy to solve.