What are the causes of the clogging of the hammer crusher?
Hammer crusher accompanied by Shandong Sanxiang Heavy Industry plant to the present 30 years, is the company's service level products, but also laid the company in the field of soft rock crushing leader status behind the scenes hero. After so many years, we know all aspects of our old friend's temperament, and we can correct any problem.
In the actual production process, a relatively high probability of occurrence is the phenomenon of blocking material, so the company set up two discharge ports at the bottom of the hammer crusher, in order to prevent it from blocking material to facilitate the discharge of the material backlog in the chamber. So what are the reasons for the blocking of the hammer crusher? The following by me according to the company's many years of production and use experience for everyone to popularize:
First of all: the material to be crushed contains more viscous impurities such as soil. Why told you before the crusher production line must pay attention to soil removal work, plugging the leakage plate is a very important reason. If the material to be broken contains too much soil, especially now in order to reduce dust to meet the requirements of environmental protection, many customers choose to add spray above the machine port, which increases the adhesion of clay, and over time will make the size of the leak plate smaller and smaller, the direct result is that the material leakage is more and more slow, the original specification of the material is broken repeatedly. It not only increases the wear cost of the machine, but also reduces the production efficiency, which is serious to a certain extent, that is, the material blockage directly causes the machine to stop.
Second: in the actual production process, because the wear-resistant leakage plate and high chromium alloy hammer are constantly wearing, with the production time getting longer and longer, the gap between the hammer head and the leak plate will theoretically become larger and larger, and a key factor in the control of the size of the hammer crusher is the spacing between them. If the distance between the two exceeds the theoretical maximum value one day, it will produce more than the material blocked in the leak plate, directly causing other materials can not be excluded, once the excessive material accumulation, it will cause the blocking phenomenon. Therefore, production workers are required to pay attention to the wear of the wearing parts of the crusher when carrying out machine maintenance, and the replacement parts must be replaced in time.
Third: the transformer power is insufficient, resulting in the motor can not run at full load, indirectly resulting in insufficient kinetic energy of the machine rotor, unable to break large materials in time, but also cause blocking phenomenon.
Fourth: The triangle belt connecting the motor and the belt pulley of the hammer crusher is loose, and the power of the motor can not be well transmitted to the crusher, resulting in insufficient kinetic energy of the crusher, and it is also unable to break large materials in time.
Fifth: the motor lack of phase, this situation is most likely to occur in the case of using two motors, one of which does not work because of the lack of phase, in fact, only one motor in the case of hard. The method of judging is to check whether the ammeter is normal. In this case, the damaged motor should be replaced immediately.
Sixth: When the eccentric shaft of the hammer crusher is loose, it will make the eccentric shaft stuck, and it will not be able to rotate again, naturally, it will not work, and then there will be a blocking phenomenon.
In summary: Shandong Sanxiang Heavy Industry Co., Ltd. according to many years of production and use experience, the main reasons for the hammer crusher plugging are the above several, so we must pay attention to the removal of soil in the production, just replace the parts should be replaced in time, transformer power must be sufficient, and pay attention to the work of the transmission system is normal. If you have any better suggestions, welcome to call Shandong Sanxiang Heavy Industry machinery service hotline to tell us.

Remark:Shandong Sanxiang Heavy Industry Co., Ltd. specializes in the crusher industry and has achieved notable accomplishments in both soft and hard rock crushing domains. The factory is a stone crusher manufacturer and sopplier from Shandong province China,with the best stone crusher quality and price for you.We can accept the MOQ order as 1 set,and the delivery time is 15days after we confirm customer order.Beginning with the hammer crusher, they have successfully developed a comprehensive range of crushing machinery and equipment, including hydraulic double roll sand-making machines, rod mill sand-making machines, roller (grinding) sand-making machines, jaw crushers, impact crushers, double roll crushers, strong impact crushers, reversible strong impact crushers, vibrating feeders, circular vibrating screens, low-oil vibrating screens, triple shaft elliptical screens, and hydraulic cone crushers. The company also offers sales of accessories such as high-chromium alloy hammerheads and wear-resistant leakage plates.