How to effectively reduce the wear cost of wear-resistant parts of various stone crusher machines?
Although in the actual production process, especially the working environment of the stone crusher mill machine

is generally extremely harsh, but we can still through scientific and reasonable management methods, effectively reduce the wear of various wear parts of the crusher and improve their service life. Shandong Sanxiang Heavy Industry Co., LTD., as a stone crusher machine manufacturer, has been committed to the research and development of wear-resistant parts of the rock crusher machine for so many years, and has accumulated a lot of experience in the use of machine parts.
So how to effectively reduce the wear cost of wear-resistant parts of stone crusher machine? Next, I have a simple discussion with you, hoping to help you.
First, believe in the power of science and technology. The stone crusher machine plant produced by our company has long helped our customers realize intelligent operation. Shandong Sanxiang rock crusher mill machine factory customers know that our rock crusher production line plant has an intelligent controller such a thing, its role is to control the feeder uniform feeding, so that the workload of the host is not loaded, can effectively protect the motor and extend its service life. At the same time, the machine to maintain normal operation, which is the basic conditions to protect the wear parts of the crusher, otherwise, due to the intermittent work of the host or insufficient power and other problems, are one of the reasons for the wear of wear parts accelerated.
Second, it is necessary to do a good job of removing soil and iron from the stone crusher machine production line plant. Clay is easy to paste everywhere, plugging the leak hole, attached to the vibrating screen, etc., resulting in a decrease in the efficiency of the machine, there will be poor material dregging, repeated impact, while affecting the output, but also increase the wear degree of the wear-resistant parts of the hammer crusher mill machine. Iron block is not to mention, light damage to the service life of broken wear parts, heavy damage to the jaw crusher, impact crusher, cone crusher and other machine bore, so the iron work must also be done.
Third: timely adjustment and replacement of wear-resistant parts of the machine. Taking the high chromium alloy hammer head of the hammer crusher as an example, when its wear does not exceed one-third, it needs to be turned around, and the hammer head can still be used as a new alloy hammer head. In addition, when the wear-resistant leakage plate is worn to a certain extent and exceeds the reasonable gap between the hammer head and it, it should be replaced in time, otherwise, the actual impact effect of the hammer head will be reduced because the gap is too large, and it is easy to cause the occurrence of material blocking. In addition, the liner is one of the machine accessories that is more prone to wear, mainly in the actual production process, it has to withstand the continuous erosion of the material. How to reduce the wear cost of the lining plate, in addition to the need to buy real materials, high-quality products, the usual maintenance work is also essential, pay attention to whether the screw loosening signs, whether there are prominent parts, these will increase the wear of its.
Fourth: wear-resistant leakage plate if the material contains high silicon content, it is recommended to thicken appropriately, because its wear level directly affects the use of the machine. Taking the hammer crusher as an example, the spacing between the leakage plate and the alloy hammer head is a certain interval, which is greater than or less than the rated interval will have a bad impact on the machine production. In the daily maintenance process, in addition to timely removal of debris from the leakage board, we should also pay attention to observe the degree of wear, and replace it when it is replaced, so as to better protect the service life of the wear-resistant leakage board.
Fifth: Develop the habit of regular maintenance. No matter how good the stone crusher production line has been used for a long time, it is inevitable that there will be various problems, which requires us to do a good job of daily maintenance and prevention.
Sixth: do the lubrication of the stone crusher. This point does not need to be extra verbose, in order to smooth and healthy operation of the machine, lubrication work must be in place.
Seventh: Let the stone crusher production line in the actual production process as far as possible to keep in a relatively good working environment, and in all aspects of production continue to improve and perfect, the work to be done to be detailed, to be implemented.
To sum up: effectively reduce the wear of various crushers wear parts of Shandong Sanxiang Heavy Industry Co., LTD. Of course, in addition to the above points, there are a lot of places that need our attention, this work is derived from practice, and then used to guide the actual production work. If you have a better way, please call the service hotline of Shandong Sanxiang stone crusher machine factory to tell us, let us do this job well together.